Genio 510-EVK

Genio 510-EVK board is an evaluation kit of MediaTek MT8370 platform, which is a high performance IoT platform with rich features. This section describes board features that are relevant to IoT Yocto.

Documentation

For Genio 510-EVK hardware documentation and the EVK User Guide, please visit the IoT Developer Home page.

Genio 510-EVK
../_images/hw_evk_g510-evk_isometric.jpg
../_images/hw_evk_g510-evk_top-view.jpg

Genio 510-EVK Ports

Ports of |G510-EVK| main board

Ports of Genio 510-EVK main board

Ports of |G510-EVK-REF-BOARD| main board

Ports on the bottom side of Genio 510-EVK main board

Block Diagram

../_images/G510_block_diagram_with_RichTek.png

Block Diagram

Packing List

S.No

Part Number or Marking

Item Name

Description

Quantity

1

IoT-Genio 510 EVK-P1V3

Genio 510 EVK main motherboard

1

2

IoT-CAM-DTB-D1V2-D2

D2 Camera Board

Smaller Raw Sensor Camera Board using IMX214 Image Sensor (not used in this QSG)

1

3

KD070FHFID015-C021A

7” LCD Panel

LCM Module

1

4

M.2 WIFI6 Module AW-XB468NF (IC: MT7921L)

WiFi Module

Installed

1

5

IPEX to IPEX cable

Installed

2

6

SMA Antenna

WiFi Antenna

Installed

1

7

12V, 4.16A AC adapter plus power cord

1

Description of kit contents

Genio 510 EVK Main Motherboard

These images show the main motherboard and relevant IO.

../_images/hw_evk_g510-evk_ports1.png

Genio 510-EVK Top View Main Motherboard

../_images/hw_evk_g510-evk_ports-btm1.png

Genio 510-EVK Bottom View Main Motherboard

D6 Camera Board

The D6 camera Board uses the ON Semiconductor AR0830 sensor. The board has two MIPI CSI paths, one connecting directly with the processor (MT837 0) on the main motherboard, and another connecting with the main motherboard through an ISP (On-Semiconductor AP1302CSSL00SMGA0-DR). These two MIPI paths are switched by a MIPI multiplexer (TI TS3DV642RUARQ1).

../_images/d6_camera_board1.jpg

D6 Camera Board

Board Feature Summary

At the current release, IoT Yocto enables the following board features:

Supported Board Features

  • MediaTek CPU (MT8370)

  • MediaTek PMIC (MT6365)

  • 4GB LPDDR4X RAM (Micron MT53E1G32D2FW-046 IT: B)

  • 64GB eMMC5.1 x 1 (KIOXIA THGBMJG9C8LBAU8)

  • 2.0mm DC Jack x 1 (for 12V DC Input)

  • Micro SD Card Slot x 1

  • Push Button x 4 (Power, Reset, Download and Home Key)

  • LEDs (Power, Reset, System on LED)

  • 4-Lane DSI x 2 (Only DSI0 supported)

  • eDP x 1

  • HDMI2.0 x 1

  • 10/100/1000M Ethernet x 1

  • USB Device Port x 1 (Micro USB Connector)

  • USB Host Port x 1 (Type-C USB Connector)

  • 3.5mm Earphone Jack x 1 (with Microphone Input)

  • 3.5mm Line Out Audio Jack x 1

  • Analog Microphone x 1

  • Digital Microphone x 2

  • UART Port x 3 for Trace Log with USB to UART Bridge IC (Micro USB Connector x 3)

  • I2C Capacitive Touch Pad

  • 4-Data Lane CSI x 2

  • M.2 Slot x 1 (PCIe & USB)

  • AzureWave AW-XB468NF WiFi Module (MT7921)

  • M.2 Slot x 1 (SDIO)

  • 40-Pin 2.54mm Pin Header x 1 (for Raspberry Pi like I/O Interface)

Unsupported Board Features

  • Charging Status LED

  • Battery Charger

  • AW-CB451NF WiFi Module (MT7663)

  • DSI1 (Only DSI0 supported)

Please refer to IoT Yocto Releases section for detailed list on supported features.

FTDI board control

The Genio 510-EVK has a FTDI FT232R chip connected to the UART0 (CN3200) port. You can control the power (PWRKEY), reset (SYSRST), and download (KPCOL0) lines through the CBUS lines of the FT232R chip:

FTDI GPIO Line

Function

0

Power (PWRKEY)

1

Reset (SYSRST)

2

Download (KPCOL0)