Genio 1200-EVK

This evaluation kit is suitable for our technology partners to evaluate the MT8395 processor for solution design and development. This section describes board features that are relevant to Android.

Important

The production version of Genio 1200-EVK is P1V2.

Documentation

For Genio 1200-EVK hardware documentation and the EVK User Guide, please visit the IoT Developer Home page.

Genio 1200-EVK
../_images/hw_evk_g1200-evk_isometric.jpg
../_images/hw_evk_g1200-evk_top-view.jpg

Genio 1200-EVK Ports

Ports of |G1200-EVK-REF-BOARD| main board

Ports of Genio 1200-EVK main board

Ports of |G1200-EVK-REF-BOARD| main board

Ports on the bottom side of Genio 1200-EVK main board

Genio 1200-EVK Block Diagram

Block diagram of |G1200-EVK-REF-BOARD|

Block diagram of Genio 1200-EVK

Packing List

S.No

Part Number or Marking

Item Name

Description

Quantity

1

Genio 1200 EVK-P1V2

Genio 1200 EVK main motherboard

1

2

IoT-CAM-DTB-D1V2-D2

D2 Camera Board

Smaller Raw Sensor Camera Board using IMX214 Image Sensor (not used in this QSG)

1

3

IoT-CAM-DTB-D1V3-D6

D6 Camera Board

Larger YUV Sensor Camera Board using AR0830 Image Sensor

1

4

KD070FHFID015-C021A

7” LCD Panel

LCM Module

1

5

M.2 WIFI6 Module AW-XB468NF (IC: MT7921L)

WiFi Module

Installed

1

6

IPEX to IPEX cable

Installed

2

7

SMA Antenna

WiFi Antenna

Installed

1

8

12V, 4.16A AC adapter plus power cord

1

Description of kit contents

Genio 1200 EVK Main Motherboard

These images show the main motherboard and relevant IO.

../_images/hw_evk_g1200-evk_ports.jpg

Genio 1200-EVK Top View Main Motherboard

../_images/hw_evk_g1200-evk_ports-btm.jpg

Genio 1200-EVK Bottom View Main Motherboard

D6 Camera Board

The D6 camera Board uses the ON Semiconductor AR0830 sensor. The board has two MIPI CSI paths, one connecting directly with the processor (MT8390) on the main motherboard, and another connecting with the main motherboard through an ISP (On-Semiconductor AP1302CSSL00SMGA0-DR). These two MIPI paths are switched by a MIPI multiplexer (TI TS3DV642RUARQ1).

../_images/d6_camera_board.jpg

D6 Camera Board

Board Feature Summary

At the current release, Android enables the following board features:

Supported Board Features

  • MediaTek CPU (MT8395IV/ZA)

  • MediaTek PMIC (MT6365IAW/B)

  • 4GB LPDDR4X RAM x 2 (Micron MT53E1G32D2FW-046 IT:B)

  • 64GB eMMC x 1 (Western Digital SDINBDG4-64G-XI2)

  • Φ2.0 DC Jack x 1 (for 12V DC Input)

  • Micro SD Card Connector x 1

  • Push Button x 4 (Power, Reset, Home and Download)

  • LED x 3 (System Power, Reset, DC-IN Power)

  • 4-Lane MIPI DSI x 2

  • 4-Lane MIPI CSI x 3

  • HDMI x 2 (IN x 1, OUT x 1)

  • LVDS x 1

  • eDP x 1

  • 10/100/1000M Ethernet x 1 (Realtek RTL8211FI-CG)

  • Micro USB x 2 (device, UART)

  • UART Port for Trace Log with USB to UART Bridge IC

  • USB Type-A 3.2 Connector x 2

  • USB Type-C Connector (USB 3.2/DP MUX)

  • 3.5mm Earphone Jack x 1 (with Microphone Input)

  • 3.5mm Line Out Audio Jack x 1

  • Analog Microphone x 3 (Merry MMA102-006)

  • Digital Microphone x 2 (Merry MMA102-007)

  • UART Port x 1 (6 PIN/2.54mm Pin Header)

  • 2 Slot Key E x 1

  • For AzureWave AW-XB468NF Wi-Fi 6 & BT 5.2 Module

  • M.2 Slot Key B x 1

  • 40-Pin 2.54mm Pin Header x 1 (for Raspberry Pi Like I/O Interface)

  • Micro SIM x 1

  • Nano SIM x 1

  • Operating Temperature: -40°C ~ 85°C

FTDI board control - not supported

The Genio 1200-EVK does not have its FTDI FT232R chip CBUS pins connected to the power (PWRKEY), reset (SYSRST), and download (KPCOL0) lines.

Therefore it is not possible to control the PWRKEY and KPCOL0 lines through the FT232R chip.