.. include:: /keyword.rst ==================== |i350-EVK-REF-BOARD| ==================== This evaluation kit is available to our technology partners to evaluate the MT8365 processor for solution design and development. This section describes board features that are relevant to |IOT-YOCTO|. Documentation ============= For |i350-EVK-REF-BOARD| hardware documentation and the EVK User Guide, please visit the `IoT Developer Home page `_. .. list-table:: |G350-EVK| :widths: 45 45 :header-rows: 0 :align: center * - .. figure:: /_asset/hw_evk_g350-evk_isometric.jpg :height: 320px :align: center - .. figure:: /_asset/hw_evk_g350-evk_top-view.jpg :height: 320px :align: center |G350-EVK| Ports ================ .. figure:: /_asset/hw_evk_g350-evk_ports.png :alt: Top view of |i350-EVK-REF-BOARD| main board :align: center :width: 75% Top View of |i350-EVK-REF-BOARD| Board Block Diagram =================== .. figure:: /_asset/i350-qsg/block-diagram.png :align: center :width: 1000px Block Diagram of |i350-EVK-REF-BOARD| and Support Status of |IOT-YOCTO| Packing List ^^^^^^^^^^^^ ===== ======================= ============================== ============================= ========= S.No Part Number or Marking Item Name Description Quantity ===== ======================= ============================== ============================= ========= 1 AIoT-i350-EVK-P1V3 Genio 350 EVK main motherboard 1 2 AIoT CAM DTB D1V2 AP1302 ISP Camera Board Camera sub-board using Onsemi AP1302 Image Sensor Processor 2 3 AP-VISION- AR0430 Appletec AR0430 Camera Module Camera Module using Onsemi AR0430 BSI CMOS Digital Image Sensor, preconnected to AP1302 ISP Camera Board 2 4 MT7663BS NGFF V10 AzureWave Wireless Module 5 Mini-SAS cable Camera Cable 2 6 TP7025C13 TFT LCM MODULE 7 LCM+TP LCD Module 1 7 I350EVK-LCM FPC-R002 LCM FPC Cable 1 8 12V AC adapter 1 9 AC cable 1 10 Plastic Standoffs 4 11 Screw 4 12 Jumper wires To jumper from AzureWave Wireless Module to PCB antennas 2 ===== ======================= ============================== ============================= ========= Description of Kit Contents ^^^^^^^^^^^^^^^^^^^^^^^^^^^ .. _main_motherboard: Genio 350 EVK Main Motherboard ------------------------------ The image shows the main mother board and relevant IO. .. figure:: /_asset/i350-qsg/Genio350-EVK-overview.png :align: center :width: 500px Genio 350-EVK main motherboard interfaces AP1302 ISP Camera Board, Appletec AR0430 Camera Module, and mini-SAS cable -------------------------------------------------------------------------- Each AP1302 ISP Camera Board can be connected to the main mother board with a mini-SAS cable. An AP1302 ISP Camera Board supports two possible MIPI CSI paths: - Connect directly with the processor (MT8365) on the Genio 350 EVK main motherboard - Connect with the main board through an ISP (On-Semiconductor AP1302CSSL00SMGA0-DR) These two MIPI paths are switched by a MIPI multiplexer (TI TS3DV642RUARQ1) which is controlled by the correct jumper selection and cabling. The small device pictured below is the Appletec AR0430 Camera Module and it features the OnSemi AR0430 image sensor. .. container:: twocol .. container:: leftside .. figure:: /_asset/sw_rity_app-dev_camera_cam-isp-mode.png AP1302 ISP Camera Board (with Appletec AR0430 Camera Module - shown left) .. container:: rightside .. figure:: /_asset/sw_rity_app-dev_camera_miniSAS.jpeg MiniSAS cable .. _azure_wave: AzureWave Wireless Module ------------------------- .. figure:: /_asset/i350-qsg/AzureWave_Bluetooth_Module.jpg :align: center :width: 200px AzureWave Wireless Module TFT LCM MODULE 7 LCM, Touch Panel, and LCM FPC Cable ---------------------------------------------------- A TFT LCM Module and touch panel can be connected to the Genio 350 EVK main motherboard with the LCM FPC Cable. Both are shown below. Please note that the demo covered in the Quick Start Guide does not use the LCM Module but rather an external HDMI Monitor. .. figure:: /_asset/i350-qsg/LCD.jpg :align: center :width: 350px LCM MODULE with FPC Cable Board Feature Summary ===================== At the current release, |IOT-YOCTO| enables the following board features: Supported Board Features ^^^^^^^^^^^^^^^^^^^^^^^^ * MediaTek MT8365 SoC * MediaTek PMIC (MT6357) * 3GB LPDDR4 RAM x 1 (Micron MT53E768M32D4DT-053) * 64GB eMMC x 1 (SanDisk/Western Digital SDINBDA4_64G) * 2.0mm DC Jack x 1 (for 12V DC Input) * Micro SD Card Slot x 1 * Push Button x 4 (Power, Reset, Volume-Up and Volume-Down) * 4-Lane DSI x 1 * HDMI x 1 * 10/100 Ethernet x 1 (Shared with DPI Signal) * USB Device Port x 1 (Micro USB Connector) * USB Host Port x 1 (Type-A USB Connector) * 3.5mm Earphone Jack x 1 (with Microphone Input) * 3.5mm Line Out Audio Jack x 1 * Analog Microphone x 1 * Digital Microphone x 2 * UART Port x 2 for Trace Log with USB to UART Bridge IC (Micro USB Connector x 2) * I2C Capacitive Touch Pad * 4-Data Lane CSI x 2 (SAS SFF-8087 Connector) * M.2 Slot x 1 (for AzureWave AW-CB451NF WiFi Module) * 40-Pin 2.54mm Pin Header x 1 (for Raspberry Pi like I/O Interface) Unsupported Board Features ^^^^^^^^^^^^^^^^^^^^^^^^^^ * 3-bit DIP Switch for Boot ID * 2-Pin 2.54mm Jumper (for IrDA Receiver) * Battery Charger * MT6631 Bluetooth/Wi-Fi/GPS/FM * SPDIF In/Out * Bluetooth function on AzureWave AW-CB451NF is not supported .. important:: IoT Yocto only provide proprietary BlueDroid stacks on MT7663. FTDI Board Control ================== The |i350-EVK-REF-BOARD| has two FTDI chips connected to the UART0 (CON461) port and to the UART1 (CON462) port. They are both able to control the power (PWRKEY), reset (SYSRST), and download (KPCOL0) lines. .. csv-table:: :header: "FTDI GPIO Line", "Function" :widths: 10, 20 "0", "Power (PWRKEY)" "1", "Reset (SYSRST)" "2", "Download (KPCOL0)"